Chase Bays Tucked Aluminum Radiator - BMW E30 / E36 / E46

QAR 2.036,00
Snap Logo Lease for as low as $/week Learn More
More Financing Options

Chase Bays

CHB CB-E306RAD-15

shopify Ships Direct from Manufacturer

-
+

The all new Chase Bays Tucked Radiator for BMW is finally here!  It's designed to free up space in BMW engine bays, improve cooling performance & Aesthetics.  This radiator is a cooling upgrade, with more fluid capacity than stock, more direct airflow, & dual pass design. It's mounted under the core support to open up to 6" of space. This radiator has been rigorously track tested on our Chase Bays E36 drift car & on countless show winning engine bays.

We've designed this all aluminum radiator to fill every bit of space under the core support while still being able to run 16" electric fan. Requires some light cutting of front core support. More mod info below.
We've integrated features no other competitor is offering. From fan sizing to modularity.

Fans

• Chase Bays 16" Fan  |  1,850 CFM  |  $82.50
• Chase Bays Race Heavy Duty Fan 16"  |  2,200 CFM |  $157.50 (4.35" thick, make sure this will clear using parallel to your core support as where fan would be mounted)

It's important that the fan is on its own relay w/ proper sized wiring & fill point is the highest point in the system. These 2 things are commonly overlooked.   We make a Dual Fan Relay Harness w/ 180º F Thermoswitch that simplifies the wiring.  We don't currently have a single fan relay harness, but will soon.

WARNING: DON'T ATTACH FAN DIRECTLY TO RADIATOR VIA FAN ZIP TIES. Over time this can wear through the core & puncture it.  Aluminum on radiator cores is very thin. This will immediately void your radiator warranty


We include threaded holes on the top & bottom header cover (see photos), if you don't use a shroud, utilize those for fan mounting brackets. 

Fill Point

Top of our radiator sits 6" lower than stock, so you have to make a new fill point. The 1st step is an inline filler neck, Click Here

Proper filler neck setup makes hose selection easier. We recommend on radiator itself w/ Raised Inline Filler Neck. (see photo) Select -20AN for 1 side of Filler Neck under options, other side will be hoses you choose. If you're using OE Push-On style Silicone Hoses, you'd select "1.5mm Normal Hose" for 1 option & "-20AN" for other. The -20AN side will thread right into the radiator then twist the filler neck onto that. W/ the thick O-Ring Seal on both sides, getting the filler neck 0º vertical is easy w/ adjustment of both sides:


Other option is putting it on upper water neck which requires some fab work. 

Modular Inlet/Outlet & Reversible Orientation

Radiator was designed to be reversible w/ interchangeable inlet/outlet types. The radiator inlet/outlet have to be on the same side b/c of the dual pass design. It looks the same on top & bottom & brackets are centered.

The inlet/outlet are -20AN female threads. Just install the adapters you need. If you change your mind later, Just thread on new adapters. We offer OE style in 1.38", -16AN, & -20AN. We recommend you put radiator inlet/outlet closer to upper water neck since that hose is more visible.

We don't recommend -16AN for 400hp+ setups!  The stock inner diameter of hose for BMW is 1.5" / 38mm. -16AN is 1" & -20AN is 1.25". By going w/ -16AN, you create restriction & reduce flow by 34%.

Hoses
Factory hoses don't work.  We piece together silicone hose bends w/ small joining couplers & use gates heat shrink clamps for a seamless install. We've been drifting our E36 non stop w/ no issues.

Eliminate the BMW expansion tank w/ this radiator if you place the fill point on the radiator as shown above. Just use a sufficient plug on the side inlet under the intake manifold & the fill point is on the radiator. This applies to M50, M52, S50, S52, S54, M60, M62, S62, etc. See below pic

Dual Pass Design

Coolant passes through TWO times instead of ONE for TWICE the cooling at half the size. Both inlets are on the same side of the radiator & a plate is welded inside b/w the 2 inlets. The radiator has 2 L brackets on each side that bolt to your core support. This radiator doesn't use any OEM radiator mounting points.

Pressure Tested

Each radiator is water pressure tested to 40psi. Your radiator shouldn’t see more than 16-19psi before the radiator cap spring does its job & expands into the overflow.

Chassis Mods

E30 lower bar has to be cut (see photos) & hood latch has to be removed plus surrounding hood latch metal trimmed. The lower bar isn't structural.

E36 slight trim to the upper grille valence on left & right side.

E46 requires no trimming at all.

You can’t run AC w/ this radiator since it takes its place.  You could custom fabricate a forward mounted condenser & extended lines.  

An intercooler can work w/ some metal valance trimming on the E30.  For the E36 & E46 light bumper trimming

FAQ, Product Revisions, & Fun Facts

Reserved for future use

 

Returns Policy

--PLEASE NOTE: MOST ORDERS ARE SUBJECT TO RESTOCK OR CANCELATION FEE. PLEASE CALL OUR OFFICE FOR DETAILS AND EXCEPTIONS-- You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).

If you need to return an item, simply login to your account, view the order using the 'Complete Orders' link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.

Shipping

We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.

When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.

Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.

Financing Options Available - Click Here for Details